载频类型可以从DRI数据中查到，载频工作状态可用disp_cell_s指令查看

多谢楼上的，能说的具体点么？还有怎么通过数据速率判定RTF类型？

disp_eq 站号 dri * * full,看下就知道是什么类型的设备了,做RTF的时候是没分设备类型的,一般GPRS是32K,有时候也会设置成16K的,EG一般是64K,而且还会说明钉琏几个时隙的

感谢回答，那能说得具体点么？32K的数据是啥？16k的数据？64k的数据？另外上站时碰到过EDGE的RTF捆绑DRI的第一块载波的情况，请解释一下，多谢拉

EDGE:


MMI-RAM 1015 -> disp_cell_s 7

Start of report for LOCATION 7:

GSM CELL ID

MCC502502502
MNC1212 12
LAC8042(1F6Ah) 8042(1F6Ah)8042(1F6Ah)
CI36741 (8F85h) 36742 (8F86h)36743 (8F87h)
RAC201(00C9h) 201(00C9h)201(00C9h)
--------------------------------------------------------------------------------
Primary Freq TypeEGSM EGSMEGSM
Secondary Freq Type N/AN/AN/A
BCCH Frequency119111108
--------------------------------------------------------------------------------
StatusUnbarredUnbarred Unbarred
GPRS StatusUnbarredUnbarred Unbarred
EGPRS StatusEGPRS AvailEGPRS Avail EGPRS Avail
PDCH StatusPD AvailablePD AvailablePD Available
RES PDCH Requested3 33
SW PDCH Requested2 22
Reset in Prog NoNo No
GPRS Reset in ProgNoNo No
SPI in ProgNoNo No
BSS BSSAP PrhbNANA NA
MSC BSSAP PrhbNANA NA
SPI/MSC SCCP PrhbNANA NA
AccClass BarNone NoneNone
GPRS AccClass Bar4 44
EGPRS Chan ReqAvailAvail Avail
Full Power ModeOFFOFFOFF
Ext Range ModeOFFOFFOFF
Active PCU Site0 00

FREEINUSE UNAVLFREEINUSE UNAVL FREEINUSE UNAVL
----- ----- ---------- ----- ----- ----- ----- -----
SDCCH15 10 16 0016 00
Norm Outer TCH/F 530 530620
Norm Inner TCH/F 000 000000
ExtOuter TCH/F 000 000000
Norm Outer TCH/H 000 000000
Norm Inner TCH/H 000 000000
Norm Outer TCH/G 0NA 0 0NA 00NA 0
Norm Inner TCH/G 0NA 0 0NA 00NA 0
PD CHANNEL 000 000000
EGPRS PD CHANNEL 500 500500
Ext PD CHANNEL000 000000
Ext EGPRS PD CHAN000 000000

End of Report.

disp_eq 站号 dri * * full,看下就知道是什么类型的设备了. CTU or CTU2

MMI-RAM 1015 -> disp_eq 7 full

DeviceFRUKit NumberSerial NumberHW Version Num
----------------- ---------------- --------------- --------------- --------------
CSFP000PCMCIA
BTP000MCUF
DRI000CTU2
DRI100CTU2
DRI010CTU
DRI110CTU
DRI200CTU2
DRI210CTU
MSI000NIU
MMS000NIU
MMS010Not Applicable
RSL000Not Applicable
RSL010Not Applicable
GCLK000MCUF
EAS1500Not Applicable
CAB1500HORIZONMACRONot ApplicableNot ApplicableUnavailable
PSU: ASCOM -48 DCNot ApplicableNot ApplicableUnavailable
PSU: ASCOM -48 DCNot ApplicableNot ApplicableUnavailable
PSU: MAG -48 DCNot ApplicableNot ApplicableUnavailable
Not ApplicableNot ApplicableNot ApplicableUnavailable
SITE000Not Applicable
PATH000Not Applicable
RTF000Not Applicable
RTF100Not Applicable
RTF200Not Applicable
RTF010Not Applicable
RTF110Not Applicable
RTF210Not Applicable

一般GPRS是32K,有时候也会设置成16K的.
MMI-RAM 1015 -> disp_eq 7 rtf 0 1
Type of carrier: NON_BCCH
RTF identifier: 0 1
Primary Unique PATH id is: 0
GSM cell to which this carrier is assigned: 502 128042 36741
Carrier absolute radio freq. channel: 96
Carrier frequency hopping indicators: 255 255 255 255 255 255 255 255
Carrier training sequence codes: 2 2 2 2 2 2 2 2
Cell zone[cell_zone]: 0
Number of extended range timeslots allowed[ext_timeslots]: 0
SDCCH load[sd_load]: 2
SDCCH placement priority[sd_priority]: 0
Channel allocation priority[chan_alloc_priority]: 0
Packet Radio Capability[pkt_radio_type]: 16K
Half Rate enabled: 0
allow_8k_trau: Yes




EG一般是64K.
MMI-RAM 1015 -> disp_eq 7 rtf 0 0
Type of carrier: BCCH
RTF identifier: 0 0
Primary Unique PATH id is: 0
GSM cell to which this carrier is assigned: 502 128042 36741
Carrier absolute radio freq. channel: 119
Carrier frequency hopping indicators: 255 255 255 255 255 255 255 255
Carrier training sequence codes: 2 2 2 2 2 2 2 2
Number of extended range timeslots allowed[ext_timeslots]: 0
SDCCH load[sd_load]: 2
SDCCH placement priority[sd_priority]: 0
Channel allocation priority[chan_alloc_priority]: 0
Packet Radio Capability[pkt_radio_type]: 64K
rtf_ds0_count[rtf_ds0_count]: 7
Half Rate enabled: 0
allow_8k_trau: Yes

哥们，辛苦了，多谢！

more:
还可以看Path ts
eg:输入disp_mms_ts_usage site.o 0
开通了GPRS的RTF一般站用4个TS。
还有就是现在开Edge都是要用一块CTU2载频，RTF捆绑DRI的第一块载波的情况是不是在Horizon I 的cab 中的CTU2呢？

是的，是ctu2在h1柜子中

呵呵,因为现在MOTO只有CTU2的载频支持EDGE, 又做BCCH的rtf不参与跳频,所以RTF捆绑DRI的第一块载波,我这边还没开EDGE,只是这样分析的.
Rainbow

学习学习。。。。。。。。。。。