问题已开启
(普通问题)
RSSI为什么往往比RSCP小?
RSSI指示的手机在所在的载频上接收到的全部功率,RSCP指示的是手机接收到的导频信道信号强度,但为什么路测时软件显示的RSSI往往比RSCP小?
提问者: 绅士涛涛 提问时间: 2013-09-02
• TD的RSSi比RSCP小是怎么回事? 2014-03-04
• RSSi和RSCP 2013-09-25
• 同一频点的RSCP分别是-40与-70的RSSi是多少? 2013-09-03
• RSSi/RSCP/ISCP 区别 2013-08-14
• 关于RSSi/RSCP/ISCP怎么理解 2013-07-05
• RSCP与RSSi的区别 2013-01-21
• Ec/Io,Ec/No与RSCP/RSSi之间的联系 2012-10-22
• RSSi和RSCP 2013-09-25
• 同一频点的RSCP分别是-40与-70的RSSi是多少? 2013-09-03
• RSSi/RSCP/ISCP 区别 2013-08-14
• 关于RSSi/RSCP/ISCP怎么理解 2013-07-05
• RSCP与RSSi的区别 2013-01-21
• Ec/Io,Ec/No与RSCP/RSSi之间的联系 2012-10-22
问题答案
( 2 )
RSCP为控制信道的功率,为了保证系统可以正常寻呼到移动台,导频信道的发射功率必须大于其它信道的发射功率5db
回答者:
lxc321365
回答时间:2013-09-02 22:14
6 2
RSRP(Reference Signal Receiving Power)是在某个Symbol内承载Reference Signal的所有RE上接收到的信号功率的平均值;
而RSSI(Received Signal Strength Indicator)则是在这个Symbol内接收到的所有信号(包括导频信号和数据信号,邻区干扰信号,噪音信号等)功率的平均值
而RSRQ(Reference Signal Receiving Quality)则是RSRP和RSSI的比值,当然因为两者测量所基于的带宽可能不同,会用一个系数来调整,也就是 RSRQ = N*RSRP/RSSI
从定义来看RSRP相当于WCDMA里CPICH的RSCP,RSRQ相当于CPICH Ec/No.
在小区选择或重选时,通常使用RSRP就可以了,在切换时通常需要综合比较RSRP与RSRQ,如果仅比较RSRP可能导致频繁切换,如果仅比较RSRQ虽然减少切换频率但可能导致掉话,当然在切换时具体如何使用这两个参数是eNB实现问题。
RSSI是系统带宽的总功率(包括噪声)-@7I.a$R1k"e7`%d
RSRP是PDSCH信道的功率bbs.mscbsc.com:V%y6p*o"c+G/E
RSRQ=系统带宽的RB个数*RSRP/RSSImscbsc
而RSSI(Received Signal Strength Indicator)则是在这个Symbol内接收到的所有信号(包括导频信号和数据信号,邻区干扰信号,噪音信号等)功率的平均值
而RSRQ(Reference Signal Receiving Quality)则是RSRP和RSSI的比值,当然因为两者测量所基于的带宽可能不同,会用一个系数来调整,也就是 RSRQ = N*RSRP/RSSI
从定义来看RSRP相当于WCDMA里CPICH的RSCP,RSRQ相当于CPICH Ec/No.
在小区选择或重选时,通常使用RSRP就可以了,在切换时通常需要综合比较RSRP与RSRQ,如果仅比较RSRP可能导致频繁切换,如果仅比较RSRQ虽然减少切换频率但可能导致掉话,当然在切换时具体如何使用这两个参数是eNB实现问题。
RSSI是系统带宽的总功率(包括噪声)-@7I.a$R1k"e7`%d
RSRP是PDSCH信道的功率bbs.mscbsc.com:V%y6p*o"c+G/E
RSRQ=系统带宽的RB个数*RSRP/RSSImscbsc
LTE Reference Signal Received Power (RSRP)
Definition
Reference signal received power
(RSRP), is defined as the linear average over the power contributions
(in [W]) of the resource elements that carry cell-specific reference
signals within the considered measurement frequency bandwidth.
For RSRP determination the cell-specific reference signals R0 according TS 36.211 [3] shall be used. If the UE can reliably detect that R1 is available it may use R1 in addition to R0 to determine RSRP.
The reference point for the RSRP shall be the antenna connector of the UE.
If receiver diversity is in use by the
UE, the reported value shall not be lower than the corresponding RSRP
of any of the individual diversity branches.
Applicable for
RRC_IDLE intra-frequency,
RRC_IDLE inter-frequency,
RRC_CONNECTED intra-frequency,
RRC_CONNECTED inter-frequency
RSSI Received Signal Strength Indicator
RSSI在每个RAT里边的定义还有一些细小的差别,看看36214协议吧
For RSRP determination the cell-specific reference signals R0 according TS 36.211 [3] shall be used. If the UE can reliably detect that R1 is available it may use R1 in addition to R0 to determine RSRP.
The reference point for the RSRP shall be the antenna connector of the UE.
If receiver diversity is in use by the UE, the reported value shall not be lower than the corresponding RSRP of any of the individual diversity branches.
RRC_IDLE inter-frequency,
RRC_CONNECTED intra-frequency,
RRC_CONNECTED inter-frequency
回答者:
OscarDon
回答时间:2013-09-02 22:51
7 13
联系我们 - 问通信专家 | Powered by MSCBSC 移动通信网 © 2006 - |